In alignment with our commitment to transparency and integrity, we want to clearly disclose that product prices and descriptions may vary on the websites of our retail partners.
We encourage you to visit the retailer's site directly for the most current images, products, prices, and descriptions.
It's important to us that you're informed Zeppy may receive compensation for some listings featured on our site.
Additionally, we want to be upfront about our use of affiliate links; our affiliations, including but not limited to the eBay Partner Network, support our mission to provide valuable content and offerings to you.
For the Article / vehicle assignment the information in the TÜV report or the ABE is decisive. For this purpose, among other things, the EC operating license number (item "K" can be found in the vehicle registration document or on the type plate of the vehicle!) must be compared with the information in the report.
Before installation, please use the parts certificate / ABE to check whether the items supplied (see parts labeling) are approved for your vehicle (see area of use). The current parts certificates / ABE's can be found at www. eibach .
If there are deviations, the parts must not be installed - please contact the seller in this case.
We recommend that Installation of our products only in a qualified workshop carried out by appropriately trained personnel and the required special tools.
the installation position can be “read” from the imprint – have the spring installed in such a way that you can read the imprint. - The number must not be "upside down".
After the spring/chassis components have been installed, a Checking the wheel setting valuesnecessary.
If the series shock absorbers are no longer fully functional and their effectiveness has noticeably diminished, we definitely recommend the Exchange for new series shock absorbers or sports shock absorbers.
at sportsline Springs we recommend the installation of sports shock absorbers such as
bilstein B8
All wheel/tire combinations that have been approved by the wheel type test centers can be used. the Conditions in the wheel report or Wheel ABE must be observed with the exception of the requirement for standard chassis.
Depending on the engine, transmission, equipment and tolerances of the vehicle, the lowering can deviate by a few mm from the specified values. The level of lowering is reduced by the level of the factory lowering.
The usability of our products refers to series vehicles. For conversions and special accessories (also applies to standard accessories!) such as the installation of a special brake system (e.g. ceramic brake system), central wheel lock, sports chassis, LPG system, etc. our products may not be able to be used. The specified dimensions refer to new vehicles that have been left in series production. Measuring points: Vertical distance from the center of the wheel hub to the lower edge of the fender. Basically, the specified dimensions are target values, which can vary depending on the vehicle.
7.
The factory-fitted spring plates are available in DB specialist workshops in thicknesses of 8-23mm. As a result, the lowering specified here can be varied.
9.
With 205/50/15 tires and 7 J x 15 rims - recommendation: installation of sport gas pressure shock absorbers of the same type.
10.
If necessary, please inquire about the source of supply from our central administration.
12.
Cannot be used with factory lowering. (OE sports suspension)
15.
Without full equipment.
16.
The special equipment considered here
includes the following points system:
air conditioner
7 points
Automatic transmission (4 + 5 cyl.) 4 points
Automatic transmission (6 cyl.) 2 points
additional heating
3 points
sunroof
2 points
SECTION
2 points
Airbag
1 point
headlight cleaning system 1 point
engine protection
1 point
Electronic seat adjustment 2 points
If the combination of additional equipment results in more than 4 additional points, the lowering kit for vehicles with special equipment must be used. The selection of the rubber pads results from the following table:
Up to and including 7 points 8 mm (1 knob)
Up to and including 13 points 13 mm (2 knobs)
Up to and including 21 points 23 mm (4 knobs)
More than 21 points The lowering kit is not suitable for this version.
18.
Except vehicles with level control.
19.
Conversion to sports dampers is required for vehicles with 6-cylinder engines.
20.
Except vehicles with four wheel drive/4WD drive.
21.
Except for vehicles with electronically controlled damping force adjustment.
22.
In connection with eibach springs or original chassis.
23.
Height-adjustable front and rear axles with coilover struts
24.
Front axle can be adjusted higher with coil spring struts, rear axle with height adjustment unit
25.
In order to ensure sufficient freedom of movement, when using the standard wheel/tire combinations, spacers required.
26.
For a lowering of more than 40 mm and a diameter of the right drive shaft greater than 42 mm, you may have to the series stabilizer must be replaced. The stabilizer set required here is available from well-stocked specialist dealers under the eibach part number: E40-85-005-01-10.
28.
Only for vehicles with electronic driving stability control
30.
Height adjustment only within the range of the values specified in the TÜV parts certificate.
32.
Except for the special models "Sportiv" and "Sport" (vehicles with Bilstein dampers)
34.
Only for vehicles with a spring strut diameter of 55 mm on the front axle
35.
Only for vehicles with a spring strut diameter of 50 mm on the front axle
36.
For vehicles with EDC, additional add-on parts from the vehicle manufacturer are required:
for the front axle: BMW part no.: strut bearing 31 331 091 709 + washer 31 331 116 983 + sleeve 31 331 110 196
for the rear axle: BMW part no.: support bearing 33 521 091 710 + support cup 33 521 090 282 + washer 33 521 092 986 + protective tube 31 331 137 932 + elastomers 33 531 091 031
37.
Only the front axle can be adjusted higher using coilover struts, the rear axle has springs and dampers
38.
Only the front axle can be adjusted higher using coilover struts, rear axle dampers
39.
In versions built after 04.2002, the piston rod attachment is recessed and covered by a cover flap (piston rod thread not visible)
42.
The spring deflection-dependent brake pressure regulator on the rear axle must be checked in accordance with the specifications in the workshop manual and replaced if necessary. be readjusted.
44.
The dampers of the HA are to be replaced with the dampers supplied.
45.
Additional original parts that are not included in the scope of delivery may be required for the installation of the chassis components. Please note the relevant technical documents (parts certificate, installation instructions), which you can view on our website.
47.
The rear dampers are to be replaced with conventional dampers.
48.
On vehicles with level dampers (marking 2R or 4R) on the rear end, these must be replaced with standard dampers marked 1U or 3U, part number: 96 80 99 98 - catalog number 48 06 443.
49.
Only for vehicles with all-wheel drive!
50.
Only for vehicles with a clamp diameter on the shock absorber at the front axle of 51 mm
52.
Only for vehicles with single-leaf suspension.
53.
Only for vehicles with two-leaf suspension and one-leaf with pad.
54.
Only permitted for vehicles with vehicle class M1G if their driving noise does not exceed 74 dB(A). The vehicle class must then be changed to M1.
56.
On vehicles with a combined fog lamp and position lamp, check whether the lower edge of the lamp is lower than 350 mm from the ground. If this is the case, additional side lights must be installed above this dimension. The standard side lights can then be deactivated by removing the light bulb and disconnecting the cable connection.
58.
not suitable for model variant "Cross"
59.
Only for vehicles with the following properties: VA: steel spring, RA: level control.
60.
Not suitable for COLT Rallyart version from 2009
61.
Suspension strut attachment with M14 screw (4-hole wheel attachment)
62.
Suspension strut attachment with M16 screw (5-hole wheel attachment)
63.
from addendum 14
65.
Please chassis no. check: this kit fits with: 10th digit = letter (A, B, ....)
66.
for 5-seater version
67.
for 7-seater version
68.
Increased axle load when towing a trailer (see parts certificate).
69.
If an individual operating license is available, acceptance according to §19/2 StVZO is required.
70.
On vehicles with electronic damper control, this must be deactivated.
71.
not suitable for version 1.6 Racing (DS3)
73.
for vehicles with front-wheel drive
74.
Standard spring plate must be used
75.
without AC (without air conditioning)
76.
Dampener with hole for thread size M12
77.
Front shock absorber outer diameter 45mm
78.
Due to the use of gas pressure technology in the B6 / B8 dampers, the level of lowering may vary slightly depending on the vehicle. In vehicles with electronic damping systems, the functionality of the damper adjustment is omitted when installing B12 suspensions. - If available, we recommend using Pro-Tronic to avoid error messages.
79.
for coil springs with an inner diameter of 116mm
80.
for coil springs with an inner diameter of 106mm
81.
for vehicles without 3. row of seats
82.
Distance of the mounting holes at the front: 58mm
84.
not suitable for vehicles with xenon lights (no holder for the level sensor of the headlight range control on the damper)
85.
Dampener with hole for thread size M16
86.
for version with short wheelbase
87.
only for vehicles without rough roads
88.
for version with standard chassis
89.
Dampener with hole for thread size M10
90.
Dampener with hole for thread size M14
91.
For versions with drum brakes
92.
For versions with disc brakes
93.
only for vehicles with base axle
94.
only for vehicles with plus axle
95.
only for screwed struts
97.
not suitable for equipment variant 1BH - bad road package
98.
for vehicles with coil springs
99.
Front shock absorber outer diameter 47mm
101.
When using the suspension, the functionality of the electronic damper control is not applicable. - The error message displayed in the on-board computer can be remedied by an authorized workshop. If available for your vehicle, we recommend using Pro-Tronic to suppress the error message.
102.
For camper versions
103.
to chassis number: 200011 ; to chassis number: 3B-YE121222
104.
to chassis number: 3B-YE121221
106.
to chassis number: 41999999
107.
to chassis number: 48999999
108.
to chassis number: 4B-Y-200000
109.
to chassis number: 4D-Y-020000
110.
to chassis number: 8D-1-030000
111.
to chassis number: 8D-1-030001
112.
to chassis number: 8D-X-200000
113.
to chassis number: 8E-2-400 000
114.
to chassis number: 8E-5-400 000
115.
to chassis number: 8E-7-400 000
116.
to chassis number: A394035
117.
to chassis number: YS3ES55CD1
118.
Type: avant-garde
119.
Model: Avantgarde, Elegance
120.
not model JC Works GP
121.
not type "iL"
122.
Model: G02
123.
Type: G02, GT, GTI
124.
Type: G07, G08
125.
Model: G07, G08, G09, G11
126.
Models: G07, G08, G09, G11, GT, GTI
127.
Type: G29, G30
128.
Type: M 030
129.
Model: M 033, except M30 Turbo
130.
Type: without EDC (electronic damper control)
131.
from chassis number: 199008 to 199209
132.
from chassis number: 199210 ->
133.
from chassis number: 3B-YE121222 ->
134.
from chassis number: 4B-1-000001 ->
136.
from chassis number: 4B-W-070001 to 4B-Y-200000
137.
from chassis number: 4D-1-000 001 ->
138.
from chassis number: 51000001 ->
139.
from chassis number: 8D-1-030000 to 8D-W-006471
140.
from chassis number: 8D-1-030001 ->
141.
from chassis number: 8D-1-030001 -> ;from chassis number: 200007 ->
142.
from chassis number: 8D-W-006471 to 8D-1-030000
143.
from chassis number: 8D-X-200000 ->
144.
from chassis number: 8D-X-200001 to 8D-1-030000
145.
from chassis number: 8E-2-400001 ->
146.
from chassis number: 8E-5-400 001 ->
147.
from chassis number: 8E-7-400 001 ->
148.
from chassis number: A394035 ->
149.
from chassis number: A394036 ->
150.
from chassis number: F054768 ->
151.
from chassis number: YS3ES55CD2 ->
153.
not for distribution in China (Taiwan)
154.
only in connection with bilstein part no. 50-174546 - can only be obtained from Fa.
155.
only in connection with BMW part no. 31 32 1 139 423 (2x) - only available from BMW original parts dealers. (stone chip protection)
156.
only in connection with BMW part no. 31 33 1139 436 - can only be obtained from BMW original parts dealers. (support bearing)
159.
without EDC
160.
If spare parts are required: The part numbers of the individual components can be found in the report under "Correction of the vehicle documents". The reports can be found at www. eibach .com – To the eibach
161.
If you need spare parts, please contact your dealer / source of supply. - Have your vehicle documents, part numbers and purchase receipts ready.
162.
Not for "Caddy Maxi" version
163.
Also for version "LPG" (gas system)
164.
only in connection with BMW part no. 33 50 6 778 572 (2x) - Purchase only from BMW original parts dealers. (stone chip protection)
166.
Production country: Great Britain
167.
up to chassis number: 7L-9-045000
168.
Only for vehicles with PASM (Electronic Damping Control).
170.
For vehicles with multi-link rear axle (independent wheel suspension)
171.
For vehicles with torsion beam rear axle (rigid axle)
174.
Not for version with spring strut on the rear axle.
175.
For vehicles with electronically adjustable dampers (standard equipment). PRO-TRONIC suppresses the error message/warning light in the display after installing sports shock absorbers/coilovers (B12/PSS) without electronically adjustable dampers. The functionality of the electronic damper setting is eliminated.
176.
For vehicles with electronically adjustable dampers (standard equipment). PRO-TRONIC suppresses the error message/indicator light in the display after installing the coilover kit (PSS). The functionality of the electronic damper setting is eliminated. The PRO-TRONIC unit is included in the set.
177.
The PRO-TRONIC set AM65-20-030-01-22 is required for vehicles with electronically adjustable dampers (standard equipment)! Please order this separately.
178.
For version "Crosstouran"
179.
Category M1G (Off-Road) vehicles must be re-registered as M1 vehicles (passenger cars).
180.
from chassis number WAUZZZ8....11201
181.
for vehicles without AMG chassis
182.
for vehicles with AMG chassis
183.
not for version " Sti "
184.
The spring plate may have to be replaced. - With set E8530-140, the existing spring plate may have to be be exchanged for the original spring plate no.: 1HO412341. With sets E8547-140 and E8550-140, the existing spring plate may have to be be exchanged for the original spring plate no.: 357412341A.
185.
to chassis number: KNEJC524875 644 788
186.
from chassis number: KNEJC524875 644 789
187.
from chassis number: WAUZZZ8....11201
188.
Type: G01, G02, 0N4
189.
Type: G01, G02, 0N1
190.
Type: G03, G04, G05, G06, G07, 0N4
191.
Type: G03, G04, G05, G06, G07, 0N1
192.
Only for vehicles without PASM (electronic damper control)
193.
Only for vehicles without air suspension
194.
for model: ZFA, not for model 3C3 (USA)
195.
not for type 3C3 (USA)
196.
Damper: VA: length: 564 mm, RA: length: 666 mm
197.
Damper: VA: length: 543 mm, RA: length: 645 mm
198.
Diameter stabilizer: 20 mm
199.
Diameter stabilizer: 21 mm
200.
Model: 0N9
201.
Type: 04N
202.
Type: G46, G57, G10
203.
for vehicles with EDC (electronic damper control)
204.
Type: G01, G04, 0N1
205.
Type: G01, G04, 0N4
206.
Type: G01, 0N1
207.
Type: G01, 0N4
208.
Type: G02, 0N1
209.
Type: G02, 0N4
210.
Only for export, not available in Germany. - (Only without parts) certificate!
Disclaimer: Prices and descriptions maybe different on retailers sites, please check the retailers website for the latest images / products / prices and descriptions. Zeppy maybe compensated for some of these listings.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Wait a moment... we're getting more products!
uk 
fr
de
es
it
us
ca
